Honeywell Building Set Bluetooth Ring Scanner User Manual

0

Out of 0 Ratings

Owner's of the Honeywell Building Set Bluetooth Ring Scanner gave it a score of 0 out of 5. Here's how the scores stacked up:

  • Reliability

    0 out of 5

  • Durability

    0 out of 5

  • Maintenance

    0 out of 5

  • Performance

    0 out of 5

  • Ease of Use

    0 out of 5
of 244
 
8 - 2
Cautions and Warnings
Warning: The Bluetooth Ring Scanner Battery Charger is to be used to charge an I.T.E. Recognized Battery pack manufactured
by Helix Co., Ltd. (Model: HNP-40, LXE, P/N 161987-0001, rating 3.7V, 750mAh). Charging any other type of battery pack in
the Bluetooth Ring Scanner battery charger is prohibited.
Warning: Use the provided AC power supply, only, with the Bluetooth Ring Scanner Battery Charger. Using any other type of
AC power supply is prohibited.
Battery Charger
• There is a risk of explosion if the Bluetooth Ring Scanner Li-Ion battery in the charging pocket is replaced by an incorrect
type. Other batteries or battery packs may burst causing injury or property damage.
• Do not insert any other type of Li-Ion battery in the Bluetooth Ring Scanner battery charging pocket.
• Do not allow cleaning agents of any kind to contact the battery charging contacts; they may be damaged. If necessary,
clean them with a soft-bristle, dry brush or compressed air.
• Disconnect the charger from AC power by pulling the plug; not the cord.
• Use care when inserting battery. Do not “slam” or slide the battery into the pocket, this could damage the charger.
• Keep dirt and foreign objects out of the battery pocket. Do not short circuit any of the contacts in the battery pocket, this
could result in injury or property damage.
• Do not disassemble or perform modifications to the charger. There are no user serviceable components in the charger.
Lithium-Ion Battery Pack
• Dispose of used Li-Ion batteries according to the instructions for the type of battery.
• When not in use, lay the battery pack contact-side up in a protected environment.
• Do not store the Li-Ion battery pack in direct sunlight or anywhere the battery pack cannot cool down.
• If the Li-Ion battery pack is hot after removal from the Bluetooth Ring Scanner, allow it to cool at room temperature or in
a cool air stream before placing it in the charger.
• Do not dispose of Li-Ion batteries into a fire. Burning will generate hazardous vapors and may cause the battery to
explode. Failure to observe this warning may result in injury from inhalation of vapors or burns from flying debris.
• Do not immerse Li-Ion batteries in water or any other liquid. If batteries are immersed, contact Honeywell.
• Do not disassemble or perform modifications to the battery. There are no user serviceable components in the battery.
• Do not place the Li-Ion battery into a pocket or toolbox with conductive objects (coins, keys, tools, etc.). A Li-Ion battery
placed on damp ground or grass could be electrically shorted.
• Do not store Li-Ion batteries above 140°F (60°C) for extended periods.
• Failure to observe these warnings could result in injury or damage to the battery from rapid discharge of energy or battery
overheating.
• Electrolyte Burns. Be careful when handling batteries. If a battery is broken or shows signs of leakage do not attempt to
charge it. Dispose of it! Lead and Nickel-based cells contain a chemical solution that burns skin, eyes, etc. Leakage from
cells is the only possible way for such exposure to occur. In this event, rinse the affected area thoroughly with water. If
the solution contacts the eyes, get immediate medical attention.
• Electrical Burns. Batteries are capable of delivering high currents when accidentally shorted. Accidental shorting can
occur when contact is made with jewelry, metal surfaces, conductive tools, etc., making the objects very hot. Never place
a charged battery in a pocket or case with keys, coins, or other metal objects.

   Find Your Products By Category