Clarion Automobile Electronics Clarion CZ702 Car CD/MP3 Player User Manual

0

Out of 0 Ratings

Owner's of the Clarion Automobile Electronics Clarion CZ702 Car CD/MP3 Player gave it a score of 0 out of 5. Here's how the scores stacked up:

  • Reliability

    0 out of 5

  • Durability

    0 out of 5

  • Maintenance

    0 out of 5

  • Performance

    0 out of 5

  • Ease of Use

    0 out of 5
of 23
 
English
7
C
Z7
02
5. OPERATIONS
Basic Operations Basic Operations
Note:
• Refer to the diagrams in “3. CONTROLS”
when reading this chapter.
CAUTION
When the unit is turned on, starting and
stopping the engine with its volume raised
to the maximum level may harm your
hearing.
Be careful about adjusting the volume.
Power on / off
Notes:
• Start the engine before using this unit.
• Be careful about using this unit for a long
time without running the engine. If you
drain the car’s battery too far, you may not
be able to start the engine and this can
reduce the service life of the battery.
1. Start the engine. The power button / knob
illumination on the unit will light up.
Engine ON
position
2. When power on rst time, you can select
initial speaker system. (Refer to “Audio
Setup”)
• INITIAL …. When powering on the unit
for the rst time, you can select a speaker
system. Check your speaker system,
choose it on the unit, and then, set your
desired sound quality referring to “Audio
Setup”.
• LOAD …. When powering on the unit for
the rst time, “LOAD” is not selected.
When this unit is turned on for the rst time,
it allows you to select a speaker system.
“NORMAL” …. FRONT 2ch / REAR 2ch /
SUBWOOFER 2ch
“2WAY” …. HIGH 2ch / MID 2ch / REAR
2ch
“3WAY” …. HIGH 2ch / MID 2ch /
SUBWOOFER 2ch
Volume adjustment
Rotate the [VOLUME] knob on the front panel
or press the [ ] or [ ] button on the remote
control.
The adjustable range of volume is 0 to 40.
CAUTION
While driving, keep the volume level at
which external sounds can still be heard.
Playing source selection
Press [SRC / ] button on the front panel or
remote control repeatedly to choose desired
playing source.
Note:
Playing source selection means selecting
which mode, such as DISC mode, RADIO
mode and AUX mode.
Display system time
Press the [DISP] button on the front panel or
[DISP] button on the remote control to switch
the display information from clock, station
information (radio mode), or track information
(CD mode).
RESET
Note:
* When the [RESET] button is pressed, preset
radio stations, titles, etc. stored in memory
are cleared.
RESET
To keep the current sound settings, when
power on rst time after reset, rotate the
[VOLUME] knob to select “LOAD”, press the
knob to conrm.
Note:
If you press the RESET button or
disconnect the back-up line after
completing the audio setup, “INITIAL /
LOAD” is displayed. In this case, the unit
functions as follows.
• INITIAL …. When powering on the
unit after RESET or the backup line is
disconnected, the audio setup in the
memory is cleared and you will need to
start from selecting a speaker system.
Choose your desirable speaker system
and set your desired sound quality
referring to “Audio Setup”.
• LOAD …. When powering on the unit
after RESET or the backup line is
disconnected, the preset speaker system
and other settings are called.
If you changed the speaker system, reset
from INITIAL.
3. Press the [SRC / ] button on the front
panel or the remote control to turn on
the power under standby mode. The unit
goes back to the last status after power
on.
4. Press and hold the [SRC / ] button on
the front panel or the remote control to
turn off the power.
Mute
Press the [MUTE] button on the remote
control to mute the volume from the unit.
Note:
Doing the operation above again or adjusting
volume will release muting.

   Find Your Products By Category