Black & Decker Chainsaw Black & Decker Chainsaw User Manual

0

Out of 0 Ratings

Owner's of the Black & Decker Chainsaw Black & Decker Chainsaw gave it a score of 0 out of 5. Here's how the scores stacked up:

  • Reliability

    0 out of 5

  • Durability

    0 out of 5

  • Maintenance

    0 out of 5

  • Performance

    0 out of 5

  • Ease of Use

    0 out of 5
of 17
 
The following precautions should be followed to minimize
kickback:
(1.) Grip Saw Firmly. Hold the chain saw firmly with both hands
when the motor is running. Use a firm grip with thumbs and fingers
encircling the chain saw handles. Chain saw will pull forward when
cutting on the bottom edge of the bar, and push backward when
cutting along the top edge of the bar.
(2.) Do not over reach.
(3.) Keep proper footing and balance at all times.
(4.) Don't let the nose of the guide bar contact a log, branch, ground
or other obstruction.
(5.) Don't cut above shoulder height.
(6.) Use devices such as low kickback chain and reduced kickback
guide bars that reduce the risks associated with kickback.
(7.) Only use replacement bars and chains specified by the
manufacturer or the equivalent.
(8.) Never let the moving chain contact any object at the tip of the
guide bar.
(9.) Keep the working area free from obstructions such as other
trees, branches, rocks, fences, stumps, etc. Eliminate or avoid any
obstruction that your saw chain could hit while you are cutting
through a particular log or branch.
(10.) Keep your saw chain sharp and properly tensioned. A loose or
dull chain can increase the chance of kickback. Check tension at
regular intervals with the motor stopped and battery removed, never
with the motor running.
(11.) Begin and continue cutting only with the chain moving at full
speed. If the chain is moving at a slower speed, there is a greater
chance for kickback to occur.
(12.) Cut one log at a time.
(13.) Use extreme caution when re-entering a previous cut. Engage
ribbed bumpers into wood and allow chain to reach full speed
before proceeding with cut.
(14.) Do not attempt plunge cuts or bore cuts.
(15.) Watch for shifting logs or other forces that could close a cut
and pinch or fall into chain.
• Power Supply - Connect chain saw battery charger to correct
voltage, that is, be sure that the voltage supplied is the same as that
specified on the nameplate of the tool.
saw stopped, finger off the switch, the guide bar and saw chain to
the rear. Remove battery and use scabbard when transporting saw.
• Maintain Chain Saw With Care - Keep tools sharp and clean for
better and safer performance. Follow instructions for lubricating and
changing accessories. Keep handles dry, clean, and free from oil
and grease.
• Disconnect Battery - Disconnect battery from chain saw when
not in use, before servicing, when tensioning chain, and when
changing accessories and attachments, such as saw chain.
• Stay Alert - Watch what you are doing. Use common sense. Do
not operate chain saw when you are tired, ill, or under the influence
of alcohol, drugs, or medication. Keep all parts of the body away
from the saw chain when the motor is operating. Before you start
the saw, make sure the saw chain is not contacting anything. When
cutting through wood, remember the chain saw cuts quickly and will
continue its downward or upward path. Stay out of its path.
• Check Damaged Parts - Before further use of the chain saw, any
part that is damaged should be carefully checked to determine that
it will operate properly and perform its intended function. Check for
alignment of moving parts, binding of moving parts, breakage of
parts, mounting, and any other conditions that may affect its
operation. A guard or other part that is damaged should be properly
repaired or replaced by an authorized service center unless
otherwise indicated elsewhere in this instruction manual. Have
defective switches replaced by authorized service center. Do not
use chain saw if switch does not turn it on and off. Do not operate a
chain saw that is damaged, improperly adjusted, or is not
completely and securely assembled. Be sure that the saw chain
stops moving when the trigger is released.
• Guard Against Kickback
WARNING: KICKBACK may occur when the nose or tip
of the guide bar touches an object, or when the wood closes
in and pinches the saw chain in the cut. Tip contact in some
cases may cause a lightning fast reverse reaction, kicking the
guide bar up and back towards the operator. Pinching the saw
chain along the top of the guide bar may push the guide bar
rapidly back towards the operator. Either of these reactions
may cause you to lose control of the saw which could result in
serious injury to user.
4

   Find Your Products By Category