4.0

Out of 1 Ratings

Owner's of the Beltronics Radar Detector RX65 gave it a score of 4.0 out of 5. Here's how the scores stacked up:
  • Reliability

    4.0 out of 5
  • Durability

    4.0 out of 5
  • Maintenance

    4.0 out of 5
  • Performance

    4.0 out of 5
  • Ease of Use

    4.0 out of 5
of 16
 
Details of Programming
14
Pilot (Power-on indication)
Note: When you are using the Dark mode,
the display will only show HD, AD, or CD,
(Highway-Dark, AutoScan-Dark, or City-
Dark).
Pilot HWY (Full description)
In this setting, RX65 will display “Highway,”
“City,” or “Auto” as its power-on indication.
(factory default)
Pilot H (Letter)
In this setting, RX65 will display “H” for
Highway, “C” for City, and “A” for
AutoScan.
Pilot V (Vehicle voltage)
In this setting, RX65 will continually display
“H” for Highway, “C” for City, and “A” for
AutoScan, and the vehicle’s voltage. If the
vehicle’s voltage drops below 10.5 volts, a
low voltage warning is displayed, followed
by an audible alert. A high voltage warning
is also given if the voltage goes above 16.0
volts. The high-voltage warning is also
followed by an audible alert.
Voice
Voice On (Voice alerts on)
In this setting, all radar, laser, and SWS (if
programmed on) alerts will be
accompanied by a digital voice.
Voice Off (Voice alerts off)
In this setting, only the audio tones will be
heard during an alert or SWS message.
Power-on Sequence
PwrOnSTD (Standard)
In this setting, each time you turn on the
RX65, it will display “BEL RX65,” “Laser,”
“Ka-band,” “K-band,” “X-band,” “Safety,”
and any changes to factory settings. (factory
default)
PwrOnFST (Fast power-on)
In this setting, the RX55 will only provide a
brief audible tone, and will display any non-
factory settings.
15
Signal Strength Meter
MeterSTD (Standard meter)
In this setting, the meter displays the band
of the received signal, and a bar graph
shows the relative signal strength. (factory
default)
MeterTHT (Threat Display)
In this setting, the meter simultaneously
tracks multiple radar signals, including
relative signal strength for each.
Note: The Threat Display feature is
explained in more detail on pages 10-11.
MeterTEC (Tech Display meter)
In this setting, the meter displays the actual
numeric frequency of the radar signal
received.
Note: The Tech Display feature is
explained in more detail on page 11.
AutoMute
aMute ON (AutoMute on)
In this setting, RX65’s audio alerts will
initially be at the volume you set, but after a
few seconds, the RX65 will automatically
reduce the volume level, to keep you
informed, but not annoyed. (factory default)
aMuteOFF (AutoMute off)
With AutoMute off, RX65’s audio alerts will
remain at the volume you set for the
duration of the radar encounter.
City Mode Sensitivity
City STD (Standard)
In this setting, when you put RX65 in the
City mode, X-band sensitivity is significantly
reduced, to reduce annoyance from X-band
intrusion alarms and motion sensors.
(factory default)
City LoX (Low X band sensitivity)
In this setting, when you put RX65 in the
City mode, X-band sensitivity is reduced
more than the standard setting. This will
reduce X band alarms from other sources
even further, but also significantly reduces
range to X band traffic radar.
City NoX (No X band sensitivity)
In this setting, when you put RX65 in the
City mode, it will not respond to any X band
signals.
WARNING: Only choose this
setting if you are absolutely certain that
there are no X band traffic radar units
where you drive.
NOTE: These settings only apply when
RX65 is operated in City mode. X-band
sensitivity is not affected when used in
“AutoScan,” or “Highway” modes.