0

Out of 0 Ratings

Owner's of the Dyson Vacuum Cleaner Dyson Vacuum gave it a score of 0 out of 5. Here's how the scores stacked up:
  • Reliability

    0 out of 5
  • Durability

    0 out of 5
  • Maintenance

    0 out of 5
  • Performance

    0 out of 5
  • Ease of Use

    0 out of 5
of 16
 
8
USING YOUR DYSON APPLIANCE
PLEASE READ thE ‘ImPORtANt SAfEtY INStRUCtIONS’ IN thIS DYSON
OPERAtING mANUAL bEfORE PROCEEDING.
RAtING PLAtE
The rating plate will be either (a) behind the clear bin or (b) on the top of the
appliance above the switches, under the wand handle. Note the serial number
before fitting the wand handle onto the appliance.
If you need to gain access to the rating plate after assembling the appliance,
follow these instructions:
– open the wand cap and pull the red tube up and away from the handle
– press in the black clip in the recess of the duct
– pull the wand handle up and off the appliance; use a constant, firm pressure.
Check to ensure your electricity supply corresponds to that shown on the rating
plate. The appliance must only be used as rated.
ASSEmbLY
Lie the appliance on its back.
Attach the cleaner head by sliding it on to the connections on the lower front
part of the ball. Ensure the electrical plug on the cleaner head fits into the
twin-block connection on the body of the appliance, which is directly above the
airway. Push firmly: the cleaner head will click into place.
Stand the appliance up straight.
Attach the wand handle by sliding it on to the top of the appliance. The spring
clip in the handle will click into place.
Ensure the hose is straight. Press the red button on the hose. Slide the wand into
the hose.
Ensure the hose and wand sit in the recess of the handle. Slide the end of the
wand down into the handle to secure it
Close the wand cap.
Slide the tool holder onto the side of the duct as shown.
Ensure the cyclone and clear bin unit is secured to the main body of the
appliance.
Attach the tools as shown. In use, the tools can be attached to either the hose or
the wand.
Wind the cable counter-clockwise around the cable hooks. Secure with the clip.
To watch a short online video visit: www.dyson.com/DC65gettingstarted
OPERAtION
Unwind the cord.
Plug the appliance into the mains electricity supply.
To switch ‘ON’ or ‘OFF’ press the power button, located as shown.
To use, recline the handle. The stabilizer stand will automatically lift up.
After use, return the appliance to the upright position, pushing it firmly into
place. The stabilizer wheels will automatically lower.
Then: unplug the appliance, coil the cord safely, put the appliance away.
Switch ‘OFF’ the appliance, unplug and ensure it is upright before:
– changing or using tools
– removing the hose or airway inspection parts.
Use the cyclone carry handle to carry the appliance.
AttAChmENtS
To release the wand, open the wand cap and pull the red tube up and away
from the handle until it clicks into place.
Should you wish to use the hose without the wand, follow the above instruction
and press the red button to release the wand from the hose.
CARPEtS OR hARD fLOORS
The brush bar will always default to ‘ON’ (spinning) each time you switch the
appliance ‘ON’ and recline it for cleaning.
The brush bar will not rotate when the appliance is upright.
To switch the brush bar ‘OFF’ (e.g. for delicate rugs and hard floors):
– switch the appliance ‘ON’
– recline the appliance
– press the brush bar ‘ON/OFF’ button – the brush bar will stop spinning.
The brush bar will automatically stop if it becomes obstructed. See ‘Brush bar –
clearing obstructions’.
Before vacuuming your flooring, rugs and carpets, check the manufacturer’s
recommended cleaning instructions.
Some carpets may fuzz if a rotating brush bar is used when vacuuming. If this
happens, we recommend vacuuming in ‘hard floor’ mode and consulting with
the flooring manufacturer.
The brush bar on the appliance may damage some carpet types. If you are
unsure, turn ‘OFF’ the brush bar.
LOOKING AftER YOUR DYSON APPLIANCE
Do not carry out any maintenance or repair work other than that shown in this
Dyson Operating Manual, or advised by the Dyson Helpline.
Only use parts recommended by Dyson. If you do not this could invalidate your
warranty.
Store the appliance indoors. Do not use or store it below 32°F. Ensure the
appliance is at room temperature before operating.
Clean the appliance only with a dry cloth. Do not use any lubricants, cleaning
agents, polishes or air fresheners on any part of the appliance.
If used in a garage, always wipe the base plate, ball and stabilizer wheels with
a dry cloth after vacuuming to clean off any sand, dirt, or pebbles that could
damage delicate floors.
VACUUmING
CAUtION:
Do not use without the clear bin and filters in place.
Fine dust such as plaster dust or flour should only be vacuumed in very small
amounts.
Do not use the appliance to pick up sharp hard objects, small toys, pins, paper
clips, etc. They may damage the appliance.
When vacuuming, certain carpets may generate small static charges in the
clear bin or wand. These are harmless and are not associated with the mains
electricity supply. To minimize any effect from this, do not put your hand or
insert any object into the clear bin unless you have first emptied it and rinsed it
out with cold water (see ‘Cleaning the clear bin’).
Powerful suction can cause the hose to ‘pull back’ – please take care.
Do not work with the machine above you on the stairs.
Do not put the appliance on chairs, tables, etc.
Before vacuuming highly polished floors, such as wood or lino, first check that
the underside of the floor tool and its brushes are free from foreign objects that
could cause marking.
Do not leave the cleaner head in one place on delicate floors.
Do not use this appliance outdoors. The Dyson Car Cleaning Kit (Model 08909)
is intended for use only inside a garage.
EmPtYING thE CLEAR bIN
Switch ‘OFF’ and unplug before emptying the clear bin.
Empty as soon as the dirt reaches the level of the MAX mark – do not overfill.
To remove the cyclone and clear bin unit, press down on the red button at the
rear of the carrying handle on the cyclone.
To release the dirt, press all the way down on the red button at the rear of the
carrying handle on the cyclone.
To minimize dust/allergen contact when emptying, encase the clear bin tightly in
a plastic bag and empty.
Remove the clear bin carefully.
Seal the bag tightly, dispose as normal.
To refit:
– close the clear bin base so it clicks into place
– push the cyclone and clear bin unit into the main body of the appliance;
it will click into place
– ensure the cyclone and clear bin unit is secure.
CLEANING thE CLEAR bIN
Remove the cyclone and clear bin (instructions above).
To separate the cyclone unit from the clear bin press the red button to open
the clear bin base. This exposes a small silver button behind the red opening
mechanism. Press the silver button and separate the cyclone unit from the clear
bin.
Clean the clear bin with cold water only.
Ensure the clear bin is completely dry before replacing.
Do not use detergents, polishes or air fresheners to clean the clear bin.
Do not put the clear bin in a dishwasher.
Do not immerse the whole cyclone unit in water or pour water into the cyclones.
Clean the cyclone shroud with a dry cloth or dry brush to remove lint and dust.
To refit:
– fit the cyclone shroud into the clear bin so that the silver button clicks and
engages
– close the clear bin base so it clicks into place
– push the cyclone and clear bin unit into the main body of the appliance;
it will click into place
– ensure the cyclone and clear bin unit is secure.
WAShING YOUR fILtERS
Your appliance has two washable filters, located as shown.
Check and wash the filters regularly according to instructions to maintain
performance.
Switch ‘OFF’ and unplug before checking or removing the filters.
The filters may require more frequent washing if vacuuming fine dust.
Wash with cold water only. Do not use detergents.
Do not put the filters in a dishwasher, washing machine, tumble dryer, oven,
microwave or near an open flame.
To remove filter A see the ‘Wash filters’ section in this Dyson Operating Manual.
After washing lay the filter on its side and leave at least 24 hours to dry
completely before refitting.
To remove filter B:
– turn the central locking dial on the outer cover of the ball counter-clockwise
until the cover is released
– lift off the cover
– turn the filter one-quarter counter-clockwise to release.
Filter B should be rinsed and tapped out until the water runs clean, then tapped
out again to ensure all excess water is removed. Leave to dry completely for
24hours.
It is normal for the filter in the ball to turn grey in color.
To refit filter B:
– refit the filter on to the ball
– secure the filter by turning it one-quarter turn clockwise.
When refitting the outer cover of the ball, keep turning the central locking dial
clockwise. When it starts to click it is locked.
To watch a short online video visit: www.dyson.com/DC65filterwash